Air Ride

Sweet Stratus · Post by **Sweet Stratus** » Sun Jan 03, 2010 8:36 pm

picked up my air ride kit last night was tested and all good to go now time to install it.

Heres the switch box

Broken Glass · Post by **Broken Glass** » Sun Jan 03, 2010 8:47 pm

Looks good. I dont think ive seen you on the forum before, Im guessing you drive a stratus? haha any pictures?

LowNSlow · Post by **LowNSlow** » Sun Jan 03, 2010 8:56 pm

The guy who got flamed on his intro... pics are there.

Looks good.... post install pics

Post by **occasional demons** » Sun Jan 03, 2010 9:02 pm

LowNSlow wrote:The guy who got flamed on his intro... pics are there.

Looks good.... post install pics, with the obligatory female enhancements

At least when we BBQ him, he gives us pics.

Sweet Stratus · Post by **Sweet Stratus** » Sun Jan 03, 2010 9:15 pm

my pics are in intro part...dont wanna post here cause it might cause problems on here...lol

Post by **occasional demons** » Sun Jan 03, 2010 9:35 pm

Don't worry, it was just a little tongue in cheek fun. Just normal pics will do.

Sweet Stratus · Post by **Sweet Stratus** » Mon Jan 04, 2010 11:28 pm

here pics of a stratus running same system as me fully up and fully down down in front and mostly down in back

here vid

LaidNeon · Post by **LaidNeon** » Thu Jan 07, 2010 10:54 pm

i'ld swap out those cylinders & get some UAS bags

Sweet Stratus · Post by **Sweet Stratus** » Thu Jan 07, 2010 11:15 pm

prob with bags on my car is that the "a" arms will rub the bags and break them. Cylinders are made for cars that dnt have alot of clearance. so cylinders are what im stuck with. I dont have same supension as neon

LaidNeon · Post by **LaidNeon** » Thu Jan 07, 2010 11:46 pm

wow didn't know cylinders were made for cars without Mac Style Struts.........i would just cut the front end up to clearance for the bags to work on the UCA. then do what ever it will take to get the rear lower.

Sweet Stratus · Post by **Sweet Stratus** » Thu Jan 07, 2010 11:49 pm

that would mean hacking my "a" arm that is messing with structure and not good for the car or my life lol

LaidNeon · Post by **LaidNeon** » Fri Jan 08, 2010 12:04 am

you would have to hack the UCA........you are adding structure to it by welding a bag plate to it. It's obvious you fail to understand what i am trying to say. Granted you wouldnt have to cut out as much as this guy (Adam) did, but you would have to add the bracing for the upper bag plates

here's a more practical look at it with the factory strut towers (whats left of them) & the other sheet metal still intact

Fuzzyneon · Post by **Fuzzyneon** » Fri Jan 08, 2010 1:36 am

LaidNeon wrote:you would have to hack the UCA........you are adding structure to it by welding a bag plate to it. It's obvious you fail to understand what i am trying to say. Granted you wouldnt have to cut out as much as this guy (Adam) did, but you would have to add the bracing for the upper bag plates

here's a more practical look at it with the factory strut towers (whats left of them) & the other sheet metal still intact

hot ass car
cut shit stratus guy

lovin it

bstc00 · Post by **bstc00** » Fri Jan 08, 2010 7:38 am

Do it....Cut it.

dtjackten · Post by **dtjackten** » Fri Jan 08, 2010 12:05 pm

*chanting* cut cut cut cut cut......

Post by **occasional demons** » Fri Jan 08, 2010 12:12 pm

Damn, ya'll soundz emo!

1972demon · Post by **1972demon** » Fri Jan 08, 2010 12:30 pm

Well if he doesn't cut shit. he won't even tuck tires or lay the kit, so what's the point of air if its not on the ground when your done.

Wicked cars dan , the red and grey one was just in mini truckin , I think.

LaidNeon · Post by **LaidNeon** » Fri Jan 08, 2010 1:00 pm

The point is ground clearance at the flip of a switch & obviously he needs to be tucking for it to look decent. I'm trying help the dude because I know cylinders aren't worth a damn. Personally I wouldn't run them on any of my rides

Post by **occasional demons** » Fri Jan 08, 2010 3:03 pm

Guys, I was kidding...

Now as to whether he takes/can afford to take your advice, is another matter.

1972demon · Post by **1972demon** » Fri Jan 08, 2010 3:45 pm

LaidNeon wrote:The point is ground clearance at the flip of a switch & obviously he needs to be tucking for it to look decent. I'm trying help the dude because I know cylinders aren't worth a damn. Personally I wouldn't run them on any of my rides

Ok the ground clearance would be a good benefit, I know I hate not being able to use a parking lot cause I'm too low. But the pictures he posted that one its tucking and the kits not even grounded. I agree by no means am I comparing my knowledge to yours but the three vehicles I have done have all been bags as well.

SlvrACR · Post by **SlvrACR** » Sat Jan 09, 2010 10:20 am

LaidNeon wrote:i'ld swap out those cylinders & get some UAS bags

x2 once you break one you will know why