2gn r/t manifold

This is the place to ask questions about your engine components like cams, valves, pistons… just anything that is generally "engine" specific. This also includes questions about exhaust systems such as exhaust manifolds, piping size, mufflers, ect...
Post Reply
02goldse
2GN Member
Posts: 357
Joined: Fri Apr 27, 2007 7:57 pm
Location: Drums,PA

2gn r/t manifold

Post by 02goldse » Thu Mar 04, 2010 1:47 am

hey guys i have some ?s about the mani. with the butterfly does it really have to be in there, cuz fuzzyneon was telling me on his he ran it no butterfly and it ran fine, idk help me out
Top
hybrid-Srt2001
2GN Member
Posts: 2759
Joined: Mon May 28, 2007 6:06 am
Location: reno/cali
Contact:
Contact hybrid-Srt2001

Post by hybrid-Srt2001 » Thu Mar 04, 2010 4:22 am

it will run fine but you will loose some mid range torque.
ImageImage
[/quote]Yup it definately needs to go lower. If its not scrapeing constantly why you are driving then its not low enough bro. :lol:[/quote]
Top
02goldse
2GN Member
Posts: 357
Joined: Fri Apr 27, 2007 7:57 pm
Location: Drums,PA

Post by 02goldse » Thu Mar 04, 2010 1:12 pm

that fine im mostly highway neway above 4k and how do i mount my tb then..?
Top
stdlystdmufn
2GN Member
Posts: 1019
Joined: Sun Feb 19, 2006 7:29 pm
Location: Indianapolis, IN
Contact:
Contact stdlystdmufn

Post by stdlystdmufn » Thu Mar 04, 2010 3:00 pm

if youre putting it on a 2gn then you need to use the stock bellows tube or get an intake for the mag, or you can make one out of exhaust pipe i know someone on here atempted it i just don't know where it was at (mybe how to but im not sure)
Image
in the middle of a DOHC and MTX swap and going with an ASP kit pwered by the S259 batmowheel
Top
02goldse
2GN Member
Posts: 357
Joined: Fri Apr 27, 2007 7:57 pm
Location: Drums,PA

Post by 02goldse » Thu Mar 04, 2010 3:09 pm

all it pretty much is is a 90 deg. bend ill just buy a piece of 90 ic piping and make it work or make my own set up
Top
User avatar
Neon4Life
2009 Silver Contributor
Posts: 4214
Joined: Tue Sep 16, 2008 1:56 pm
Location: Indiana

Post by Neon4Life » Thu Mar 04, 2010 3:11 pm

not to thread jack.. but the piece that goes between the manifold and the throttle body is a 20 degree bend correct ?
Official "I'm Going to Drive My Neon till it Dies" Club #000048
Top
acr
BANNED
Posts: 403
Joined: Thu Jan 21, 2010 3:49 pm

Post by acr » Thu Mar 04, 2010 4:56 pm

no its a 45 degree bend 2.25 inch pipe.
Top
DoubtedNeon
2GN Member
Posts: 1483
Joined: Mon Jun 16, 2008 5:28 pm
Location: Larsen, Wisconsin, 54947

Post by DoubtedNeon » Thu Mar 04, 2010 11:55 pm

ya its 45, I just did this. and it sucked.
Image
Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine.. :twisted: :bootyshake: \:D/
Top
occasional demons
Junior Admin
Posts: 20064
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Fri Mar 05, 2010 12:07 am

DoubtedNeon wrote:ya its 45, I just did this. and it sucked.
:D It's supposed to suck.

But now, yours gets force fed.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
Top
DoubtedNeon
2GN Member
Posts: 1483
Joined: Mon Jun 16, 2008 5:28 pm
Location: Larsen, Wisconsin, 54947

Post by DoubtedNeon » Fri Mar 05, 2010 12:25 am

lol. ^ Love this so much <3
Image
Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine.. :twisted: :bootyshake: \:D/
Top
User avatar
Neon4Life
2009 Silver Contributor
Posts: 4214
Joined: Tue Sep 16, 2008 1:56 pm
Location: Indiana

Post by Neon4Life » Fri Mar 05, 2010 7:46 am

acr wrote:no its a 45 degree bend 2.25 inch pipe.
oo snap. ok. my bad.

DoubtedNeon wrote:ya its 45, I just did this. and it sucked.
u fool. you told me it was a 20 degree bend yesterday when i asked ya. its ok tho.
Official "I'm Going to Drive My Neon till it Dies" Club #000048
Top
occasional demons
Junior Admin
Posts: 20064
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Fri Mar 05, 2010 8:43 am

Neon4Life wrote:
acr wrote:no its a 45 degree bend 2.25 inch pipe.
oo snap. ok. my bad.

DoubtedNeon wrote:ya its 45, I just did this. and it sucked.
u fool. you told me it was a 20 degree bend yesterday when i asked ya. its ok tho.
A good suck will put a little more curl in about anything. :rofl:
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
Top
Caraudioholic24
2GN Member
Posts: 4135
Joined: Sat Mar 22, 2008 1:56 am
Location: Cumberland R.I.

Post by Caraudioholic24 » Fri Mar 05, 2010 9:33 am

If you are in need of the actuator motor pm me. I have a used one.
Image
Top
02goldse
2GN Member
Posts: 357
Joined: Fri Apr 27, 2007 7:57 pm
Location: Drums,PA

Post by 02goldse » Sat Mar 06, 2010 12:13 am

back on topic would be nice haha
Top
Post Reply

Return to “Engine”