2.2 turbo?
- neonjake27
- 2GN Member
- Posts: 92
- Joined: Thu Mar 18, 2010 8:31 am
- Location: Wadstucky,ohio
2.2 turbo?
i was lookn into turboing my sohc and was lookn for turbos from the 2.2 or 2.5 turbo group but which one should i use?
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
-
occasional demons
- Junior Admin
- Posts: 20067
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Lol, if only they came with one.DoubtedNeon wrote:a 2.0 dodge neon turbo
Bill
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
Probably shouldn't listen to anything your penis says, that guy's a dick.
Too much time spent here is a sign of a bad case of Ownaneonvirus.Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
of course you would suggest that, since he'd have to buy your adapter plate lolDoubtedNeon wrote:srt turbo works well
Justin
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
lol, well i did just finish my turbo setup, which took me all winter.

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
- neonjake27
- 2GN Member
- Posts: 92
- Joined: Thu Mar 18, 2010 8:31 am
- Location: Wadstucky,ohio
-
occasional demons
- Junior Admin
- Posts: 20067
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
As for the manifolds, no they won't bolt to the neon head. I'm sure the turbo could be made to work, but at what cost per HP gain?
The best route would to go with a known set up that works with the 2.0 neon.
Getting a turbo from a 20 year old car is likely to have some negative issues.
The best route would to go with a known set up that works with the 2.0 neon.
Getting a turbo from a 20 year old car is likely to have some negative issues.
Bill
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
Probably shouldn't listen to anything your penis says, that guy's a dick.
Too much time spent here is a sign of a bad case of Ownaneonvirus.Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
- neonjake27
- 2GN Member
- Posts: 92
- Joined: Thu Mar 18, 2010 8:31 am
- Location: Wadstucky,ohio
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
ya right. ull spend more money on something thats not going to work as well.
srt turbo the car or ASP turbo the car.
I reccomend ASP, but if u cant afford it, srt.
do it right or ur gonna regret doing it.
srt turbo the car or ASP turbo the car.
I reccomend ASP, but if u cant afford it, srt.
do it right or ur gonna regret doing it.

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
- neonjake27
- 2GN Member
- Posts: 92
- Joined: Thu Mar 18, 2010 8:31 am
- Location: Wadstucky,ohio
How do you figure that? Forward Motion makes upgraded turbos for the stock manifold, as well as an upgraded manifold. Not to mention the wide assortment of upgrades from other companies.neonjake27 wrote:but what about like a 16g off an eclipse though? ive heard people using those before. i just dont want the srt turbo cause there minimal room for inprovement.
Even the stock turbo will support up to 320hp with other support mods. So what do you mean?
If I could just figure out how to meld the Outback and the Neon into one car...


-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
I think you need to do some research on turboing your car before you start to get into this.
Lets look at my setup, I bought the cheapest reliable turbo (srt turbofold) and made an adaptor plate for it.
After running the piping, oil and coolant lines, mounting the IC and wiring the megasquirt as well as swapping injectors and fitting new sensors, running vaccum lines and a boost controller and installing the new guages and tuning, the turbo and the manifold come out to be a small percentage to a huge project. If u wanted to, u could buy an asp turbo manifold and turbo right now and be all the better.
In truth, u can swap that turbo for anything u want later on, but getting your car READY for boost is where all the work comes in.
Do some research, or ask some questions around the forced induction area. Once u figure out how and what you need, then start adding up what parts u need, and start stockpiling.
Lets look at my setup, I bought the cheapest reliable turbo (srt turbofold) and made an adaptor plate for it.
After running the piping, oil and coolant lines, mounting the IC and wiring the megasquirt as well as swapping injectors and fitting new sensors, running vaccum lines and a boost controller and installing the new guages and tuning, the turbo and the manifold come out to be a small percentage to a huge project. If u wanted to, u could buy an asp turbo manifold and turbo right now and be all the better.
In truth, u can swap that turbo for anything u want later on, but getting your car READY for boost is where all the work comes in.
Do some research, or ask some questions around the forced induction area. Once u figure out how and what you need, then start adding up what parts u need, and start stockpiling.

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
- neonjake27
- 2GN Member
- Posts: 92
- Joined: Thu Mar 18, 2010 8:31 am
- Location: Wadstucky,ohio
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
well, a small turbo isnt gonna be any better than a big one, in fact a smaller turbo is gonna make more tq which will really screw ur rods. Ide go with a larger turbo and fan my powerband out a little bit

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
Junkyard turbo ftwneonjake27 wrote:i know exactly what i need i just want a small turbo for my stock motor now to keep me ocupied.. cause i have another motor im building now with a holset hx35. just lookn for cheapest way to turbo my motor.
Idk what everyone else is talking about, a junkyard turbo build will work fine.
Check out my progress log yo... boosted for around 2gs
Budget Boost FTW
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
so uve been boosted for 2000 miles? hows it holding up? i figure about 10k before all the bugs are worked out and u know that everythings gonna last.

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
-
esteinmaier
- Supporting Vendor
- Posts: 3324
- Joined: Fri Dec 09, 2005 3:40 pm
Junkyard turbos work. So do leaf blowers, and it's dyno proven. Do they work well? That depends on what you are using. If I found an s362 in a junkyard, it would work pretty good in a drag car. But you won't find em.
ASP - First NGC SOHC in the 13s and the 12s. First SOHC neon over 500whp. First NGC Neon on MS.
Winston Churchill wrote:Yes, Madam, I am drunk, but in the morning I shall be sober and you will still be ugly.
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
ah, well in any case, ericks great, nice guy and he knows what hes doing.
btw eric.... i wanna turn the boost up..what to do?
btw eric.... i wanna turn the boost up..what to do?

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
Getting back on topic, to the OP: Of course a junkyard setup is possible, but considering the fact that almost no one does it these days on these engines, you're gonna have to figure it out for yourself. Sounds like you know what you're doing, so why the questions?
Nothing from a 2.2/2.5/2.4 turbo setup will bolt up to the 2.0. Does that help?
Nothing from a 2.2/2.5/2.4 turbo setup will bolt up to the 2.0. Does that help?
-Derek
|Donate to 2gn|Feedback || OB's | GozziFab | All Business |
|Donate to 2gn|Feedback || OB's | GozziFab | All Business |
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
^ no you can make it, he can buy it 
Justin
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823
-
DoubtedNeon
- 2GN Member
- Posts: 1483
- Joined: Mon Jun 16, 2008 5:28 pm
- Location: Larsen, Wisconsin, 54947
LOL. fact^
idk why people insist on making work for themselves.
idk why people insist on making work for themselves.

Swordfish2Cowboy wrote:They left a pry bar? Well get the prints like they do on CSI, and track those fuckers down. Then cap them.
grindpunk16 wrote: You and about 2 dozen other folks want that cover. It came with the car, and it's all mine..![]()
![]()
He's trying to save money. Outside the Neon world, JY turbos are pretty popular. I heard about a local CRX that had a $1000 setup and was blowing everyone's doors off sleeper style. Unfortunately, our engines don't have all the R&D that the Honda guys do, so we have to sort things out the long hard way. Engine management is a big issue too.
-Derek
|Donate to 2gn|Feedback || OB's | GozziFab | All Business |
|Donate to 2gn|Feedback || OB's | GozziFab | All Business |
-
racer12306
- Junior Admin
- Posts: 16015
- Joined: Sun Oct 24, 2004 8:53 pm
- Location: Baltimore, MD
- Contact:
There's no such thing as cheap and easy when it comes to a Neon.DoubtedNeon wrote:LOL. fact^
idk why people insist on making work for themselves.
There is however cheap and hard.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
