LaidNeon -- Deb's Yota (DONE)
ouch.. looks like you have your hands full. That is going to be a biatch if its all one piece. Or somehow figure out a way to disconnect the shifter so you could keep it all one piece and the slip a pin or something to reconnect the shifter.
| Nathan |

Official "I'm Going to Drive My Neon til it Dies" Club Member # 72
Semper Fi!!! USMC

Official "I'm Going to Drive My Neon til it Dies" Club Member # 72
Semper Fi!!! USMC
-
03silversxt
- 2GN Member
- Posts: 160
- Joined: Sun Jun 05, 2005 1:23 pm
- Location: Weslaco, TX
its basically going to be 2 pieces & the piece that flows into the dash will have a removable top so i can install itNeonOn19s wrote:ouch.. looks like you have your hands full. That is going to be a biatch if its all one piece. Or somehow figure out a way to disconnect the shifter so you could keep it all one piece and the slip a pin or something to reconnect the shifter.
- Dan
Finally got the truck all wrapped up as far as fab work goes. I dropped the truck off last night with my boy Brian at RF Customs to slap some paint on a few things. Then it comes back for final assembly. Haven't figured out if we should wrap the sides in black leather or the same black carpet. I'm leaning towards the carpet but we shall see if it gets painted


As you can see from the pic, the seam just wasn't thought out correctly so i moved it





As you can see from the pic, the seam just wasn't thought out correctly so i moved it



- Dan
well i got the truck all done & its currently in Vegas for SEMA. So here's some pics to show the rest of the progress
Freshly Painted Liners

Striped the darker purpler with a lighter purple outline courtesy of my boy Big Johnson

Test fitting the console after paint

got the sub hooked up

This is where my Halloween weekend started to go to shit lol. Thursday evening i started the final installation / clean up of the truck

Interior almost done

Had my baby helping me polish the wheels


Interior all buttoned up

Since the compressors were sponsored, they had to be visible inside the bed. this is a temporary setup for SEMA so this will change

By morning i was all done with her & got her loaded on the trailer to haul it to Austin (3.5 hrs) from my home so another club member could haul the taco & his ladies C10 that they built to SEMA

I left my house around 10.30 & my buddy told me to be prepared to work. I thought he was kidding cause he was literally killing himself to get this truck ready I roll up on his house to see the truck in this condition

Interior guy was almost finished & the front suspension was all torn off. Brakes still needed to go on, motor still needed to be wired, & the air suspension needed to be plumbed & wired Needless to say we werent able to get the motor wired up but we got everything knocked out before morning.

I left his house after we unloaded the taco & it was around 4 am & i drove home (3.5hrs i remind you). So all in all i was up for 2 days straight & slept all weekend. I didnt party saturday night & i didnt trick or treat sunday night lol. I can say it was all worth it cause these truck came out sick!!

Need to get some motor shots because its just as pretty as the exterior lol






Freshly Painted Liners

Striped the darker purpler with a lighter purple outline courtesy of my boy Big Johnson

Test fitting the console after paint

got the sub hooked up

This is where my Halloween weekend started to go to shit lol. Thursday evening i started the final installation / clean up of the truck

Interior almost done

Had my baby helping me polish the wheels


Interior all buttoned up

Since the compressors were sponsored, they had to be visible inside the bed. this is a temporary setup for SEMA so this will change

By morning i was all done with her & got her loaded on the trailer to haul it to Austin (3.5 hrs) from my home so another club member could haul the taco & his ladies C10 that they built to SEMA

I left my house around 10.30 & my buddy told me to be prepared to work. I thought he was kidding cause he was literally killing himself to get this truck ready I roll up on his house to see the truck in this condition

Interior guy was almost finished & the front suspension was all torn off. Brakes still needed to go on, motor still needed to be wired, & the air suspension needed to be plumbed & wired Needless to say we werent able to get the motor wired up but we got everything knocked out before morning.

I left his house after we unloaded the taco & it was around 4 am & i drove home (3.5hrs i remind you). So all in all i was up for 2 days straight & slept all weekend. I didnt party saturday night & i didnt trick or treat sunday night lol. I can say it was all worth it cause these truck came out sick!!

Need to get some motor shots because its just as pretty as the exterior lol






- Dan
-
Ntyvirus1
- 2009 Silver Contributor
- Posts: 2103
- Joined: Tue Mar 25, 2008 4:30 pm
- Location: Orlando, FL
not a fan of the blue and white one but the white truck is crazy and the ram looks great. time for neon updates?...please
Official "I'm Going to Drive My Neon till it Dies" Club #000038
hul kogan wrote: And from thy shadows he comes to rippeth thine buttholes. :lol
MoxHair wrote:You should never throw parts at a car.. You'll dent the exterior.
- TheRandom1
- 2GN Veteran
- Posts: 9938
- Joined: Mon Jan 02, 2006 11:17 pm
- Location: Chicagoland
- TheRandom1
- 2GN Veteran
- Posts: 9938
- Joined: Mon Jan 02, 2006 11:17 pm
- Location: Chicagoland




