SXT Wheels on SRT?
SXT Wheels on SRT?
So I read the sticky and discovered too late that the SXT rims will not clear the SRT brakes in the front, only in the rear. So my questions is basically is there anything I can do to make the SXT rims fit on the front of the SRT maybe with spacers or something so that it will clear the calipers? Thanks
-Mike
-Mike
TNK wrote:fertilized Hagan's potatoes? is that some slang for "i shit on Hagan's ballsack?"
- sidepipe87
- 2009 Silver Contributor
- Posts: 9501
- Joined: Fri May 30, 2008 5:35 pm
- Location: Pittsburgh, PA
- Contact:
My guess is spacers will do the trick. I know plenty of 15" wheels can be run so I'd assume it's an interference issue with the spokes and a small spacer would work.
PM me for your 03+ PCM SKIM/VIN flashing needs. Neon PCMs Plus
I know dick about spacers so maybe like 5mm will do the trick. Im pretty sure thats as big as they can go without needing longer studs?sidepipe87 wrote:My guess is spacers will do the trick. I know plenty of 15" wheels can be run so I'd assume it's an interference issue with the spokes and a small spacer would work.
TNK wrote:fertilized Hagan's potatoes? is that some slang for "i shit on Hagan's ballsack?"
- sidepipe87
- 2009 Silver Contributor
- Posts: 9501
- Joined: Fri May 30, 2008 5:35 pm
- Location: Pittsburgh, PA
- Contact:
Correct. Yeah, I'd wait for someone to chime in that has firsthand experience with this as I don't have an SRT nor have I run spacers but you are correct about not wanting to run much more than 5mm on stock studs
PM me for your 03+ PCM SKIM/VIN flashing needs. Neon PCMs Plus
Good info to know !!invujerry wrote:5MM spacers will work fine. My buddy runs snowflakes on his SRT daily.
- Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-
heydockyle
- 2011 Silver Contributor
- Posts: 4829
- Joined: Mon Jul 14, 2008 6:09 pm
- Location: Uniontown, Pennsylvania
I'm sure there is...I would have been wise for me to consult such a sticky before this whole ordeal haha. Anyway I'm just returning the 3mm and getting 5mm. They recommend extended studs with 5mm spacers but modern said as long as the are isn't driven hard (and it won't be) that it wont be a problem to forgo the studs. They also said they have never had any negative reports of failure with 5mm spacers and stock studs...heydockyle wrote:Is there a list anywhere of what 15" wheels will fit Srt's?
TNK wrote:fertilized Hagan's potatoes? is that some slang for "i shit on Hagan's ballsack?"
- sidepipe87
- 2009 Silver Contributor
- Posts: 9501
- Joined: Fri May 30, 2008 5:35 pm
- Location: Pittsburgh, PA
- Contact:
-
heydockyle
- 2011 Silver Contributor
- Posts: 4829
- Joined: Mon Jul 14, 2008 6:09 pm
- Location: Uniontown, Pennsylvania


