Shfiter Cable or Rods?

blackjack23 · Post by **blackjack23** » Tue Aug 02, 2011 10:05 am

are the shifter cables, cables or rods? and is there any way to ghetto these so i don't have to spend 166$ from the dealer?

Post by **racer12306** » Tue Aug 02, 2011 12:04 pm

What did you break?

blackjack23 · Post by **blackjack23** » Tue Aug 02, 2011 1:27 pm

i don't think i broke anything, but the garage that redid my clutch told me that the plate on top of the trans was worn, adn that my shift cables or rods were stretched.. idk what that could mean..

Post by **occasional demons** » Tue Aug 02, 2011 2:13 pm

You have levers on shafts that go into your trans. My bet is you just need some Booger Bushings.

blackjack23 · Post by **blackjack23** » Tue Aug 02, 2011 3:15 pm

hmm, is there any way i can get it shipped to canada? and are they hard to install? i was gonna need them anyways

NOTE: it feels liek tehres a lot of play in the shifter when in gear

Post by **occasional demons** » Tue Aug 02, 2011 3:57 pm

www.boogerbushings.com

JeffB#2 sells them.

JeffB#2 · Post by **JeffB#2** » Tue Aug 02, 2011 6:11 pm

I ship bushings to Canada about twice a week, on average. No extra cost to ship to Canada.

Donkeypuncher · Post by **Donkeypuncher** » Tue Aug 02, 2011 11:41 pm

blackjack23 wrote: NOTE: it feels liek tehres a lot of play in the shifter when in gear

Yup, the boogers will fix that real fast.

John Figueroa · Post by **John Figueroa** » Sat Jun 16, 2012 10:24 pm

I was thinking about picking me some Boogers, then I found some Aluminum bushings for the same price... So I told myself... "Self... your not a metalurgist Im pretty sure that Aluminum is harder than Urethane"

so My question is, has anyone ever used these? and if you have what is your opinion, these will be going on a stock shifter for now that will be cut down, and eventually replaced with a STS once I can convince my wife to let me drop the money for one.

http://www.ebay.com/itm/03-05-Dodge-Neo ... b1&vxp=mtr

Post by **occasional demons** » Sat Jun 16, 2012 10:34 pm

You must also ask yourself, what is going to wear faster?

Answer: The aluminum.

The boogers will outlast the car. There is essentially no play with the boogers.

If you are pushing hard enough to compress the booger bushings, you are going to screw up your MTX. /end of story.

Edit: Oh, and there are no clips required with boogers. No need to yell "Jesus, where the F*ck did that clip go?" Because it is about guaranteed you will lose one.

Buy the BOOGERS!

John Figueroa · Post by **John Figueroa** » Sun Jun 17, 2012 2:47 am

well car maintanence wouldnt be car maintnence with out say "Jesus Fucking Christ" would it?

Post by **occasional demons** » Sun Jun 17, 2012 7:40 pm

Only if I bleed.

Any other time, it is "Fuckingstupiddumbassbackwardsbraindeadengineers!"

Danteneon · Post by **Danteneon** » Mon Jun 18, 2012 9:26 am

One other thing to note...that Ebay set is for a SRT. The regular Neon uses 3 small bushings and one large one that doesn't come in that set.

You should still get the Boogers.

Hudson_Neon · Post by **Hudson_Neon** » Mon Jun 18, 2012 10:22 am

If you use the aluminim ones, you WILL have to do upkeep on them and eventually replace them. If you use the boogers, you'll replace them and never have to look at them again. That's called fixing a problem

John Figueroa · Post by **John Figueroa** » Mon Jun 18, 2012 8:44 pm

Alright, we have a winner, it looks like Boogers, I pick you

2GN.ORG

Shfiter Cable or Rods?

Shfiter Cable or Rods?

revival