How can i make my engine louder?

Have a question that your not sure what category it fits into or isn't really a specific question about a specific part? Ask it here...
venum_us_2002
Fresh Fish
Posts: 1
Joined: Mon May 15, 2006 3:43 pm

How can i make my engine louder?

Post by venum_us_2002 » Mon May 15, 2006 3:44 pm

I have a stock 2005 neon sxt atx. How can i make the engine louder w/ out $$$$.. Gotta love that sound.

cgneon
2GN Member
Posts: 1734
Joined: Tue May 03, 2005 11:10 pm
Location: JUPITER, FL

Post by cgneon » Mon May 15, 2006 3:52 pm

take out the resonator in the fender, (or take the airbox out completely and clamp the filter to the TB). and take off your muffler..

you'll be loud as f%*k, but still slow as hell...
Image
Official "I'm Going to Drive My Neon till it Dies" Club #000082

boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 3:53 pm

hey i was jw does taking the resinator out do anything bad?
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

marakka
2GN Member
Posts: 1396
Joined: Thu Nov 03, 2005 3:40 pm
Location: Cincinnati

Post by marakka » Mon May 15, 2006 4:04 pm

Makes it easier to suck water into your air box. Other than that..... No.
Image
LilSparkPlug wrote:Rofflies! :) I <3 you Marraka.

User avatar
MoxHair
2GN Member
Posts: 3801
Joined: Mon Feb 27, 2006 5:41 pm
Location: Atwater, CA; Orlando, FL
Contact:

Post by MoxHair » Mon May 15, 2006 4:04 pm

no the resonator just makes it quieter.

take it out..

DO IT
2017 Subaru WRX STI
Road Racing > Autocross > Spirited Driving > Sitting in Traffic > Mowing Lawns > Drag Racing

boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 4:05 pm

godamtn i just tried to find it...where the hell is it? i looked under the driverside front wheel well.
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

dangerdavex2
2GN Member
Posts: 215
Joined: Sun Apr 16, 2006 2:06 am
Location: Lancaster County, PA

Post by dangerdavex2 » Mon May 15, 2006 4:07 pm

Take the cover off of the airbox and run an open airbox. It has a nice low grumble until about 4000 rpms, then it screams. Just take the intake resonator out too.Buy the KN filter too for an open airbox, seeing as it will get dirtier quicker.
1996 Neon DOHC- 2/7/2005-6/11/05
2001 Motorsports Edition- 6/21/05-9/20/06
2007 Mazda3 Grand Touring- 2.3 Liter/5 speed manual
1997 SOHC Sport Coupe 5 speed- The project Neon
Image

User avatar
MoxHair
2GN Member
Posts: 3801
Joined: Mon Feb 27, 2006 5:41 pm
Location: Atwater, CA; Orlando, FL
Contact:

Post by MoxHair » Mon May 15, 2006 4:09 pm

05neonsxt wrote:godamtn i just tried to find it...where the hell is it? i looked under the driverside front wheel well.

I had to jack my car up and take the fender well out to get to mine. 3 bolts and that big hunk of plastic was gone.
2017 Subaru WRX STI
Road Racing > Autocross > Spirited Driving > Sitting in Traffic > Mowing Lawns > Drag Racing

boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 4:09 pm

WHERE IS THE RESONATOR!!!!! hah sorry but i wanna get it out and go for a ride in it b4 my parents get home and see me messen with my car.

edit: Just saw the post above
Last edited by boostinss on Mon May 15, 2006 4:10 pm, edited 1 time in total.
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

User avatar
MoxHair
2GN Member
Posts: 3801
Joined: Mon Feb 27, 2006 5:41 pm
Location: Atwater, CA; Orlando, FL
Contact:

Post by MoxHair » Mon May 15, 2006 4:10 pm

driver's side fender well
2017 Subaru WRX STI
Road Racing > Autocross > Spirited Driving > Sitting in Traffic > Mowing Lawns > Drag Racing

boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 4:10 pm

Anyone have n e pics or can xplain what it looks like?
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

sullygully
2GN Member
Posts: 1267
Joined: Mon Aug 08, 2005 8:23 pm
Location: Banff, Alberta

Post by sullygully » Mon May 15, 2006 4:10 pm

you have to take your drivers side wheel off, pry back the splash guard, and there you will see the infamous black box. Unscrew the bolts and fire it into the trash!
Last edited by sullygully on Mon May 15, 2006 4:34 pm, edited 1 time in total.

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Mon May 15, 2006 4:14 pm

sullygully wrote:you have to take your drivers side wheel off, pry back the splash guard, and there you will see the infamous black box. Unscrew the bolts and fire it into the trash!
there ya go. its behind the fender lining (black plastic). attaches to the airbox via an elbow (also plastic) that runs into a hole in the drivers side fender. the res isnt visible from the outside/engine bay.
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 4:26 pm

yeah i saw a tube that runs from the airfilter box into the fender wall ...im guessign thats where it is at.

btw i just took a ride around the block w/ out the airbox lid and damn does it sound nice with that low grumble...cant wait to see how it sounds when i get that res out.
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

marakka
2GN Member
Posts: 1396
Joined: Thu Nov 03, 2005 3:40 pm
Location: Cincinnati

Post by marakka » Mon May 15, 2006 4:28 pm

*LOL* You guys are gonna have this fella bashin his head off the wall.

You'll need to remove the headlight on the drivers side. When you look down into the fender well you can see it. Its a LARGE black box. Its shaped like the fender and is a HUGE pain to get out. There is a bolt along the top edge that you'll need to remove. Then take the first 2 screws out of the inner fender lining along the edge of the bumper where the tire is. Pry that back and under there is one more bolt to take it out. I took that side of my bumper loose to get mine out as I didn't want to pry against anything that hard. There is a elbow that locks the box into the frame rail right there so that it can't fall otu the bottom with the bolts removed. You have to slide the box back towards the wheel and then it can come down. Good luck.... it wasn't fun getting mine out.
Image
LilSparkPlug wrote:Rofflies! :) I <3 you Marraka.

User avatar
EmersonHart13
2GN Member
Posts: 432
Joined: Wed Apr 19, 2006 10:28 pm
Location: Chicago, IL
Contact:

Post by EmersonHart13 » Mon May 15, 2006 4:32 pm

Driving with no muffler sounds sweet. I tried it yesterday! Haha.... The drone is horrible...

John

born2speed85
n00b
Posts: 5
Joined: Sat May 13, 2006 5:48 pm

Post by born2speed85 » Mon May 15, 2006 5:03 pm

Just run open header. I did that and it sounds like a drag car. But warn the neighbors or they will probably call the cops because it will rattle some windows. Just unbolt the cat and start it up and you will know what I am talkin about.
04 sxt, mtx, pacesetter header, short shifter, vibrant strut bars, 40 series flowmasters, turbo intake, progress sways, and IAT chip

User avatar
Canada
Junior Admin
Posts: 4816
Joined: Tue Jun 28, 2005 4:05 pm
Location: Island Grove, Ontario, Canada

Post by Canada » Mon May 15, 2006 5:06 pm

marakka wrote:*LOL* You guys are gonna have this fella bashin his head off the wall.

You'll need to remove the headlight on the drivers side. When you look down into the fender well you can see it. Its a LARGE black box. Its shaped like the fender and is a HUGE pain to get out. There is a bolt along the top edge that you'll need to remove. Then take the first 2 screws out of the inner fender lining along the edge of the bumper where the tire is. Pry that back and under there is one more bolt to take it out. I took that side of my bumper loose to get mine out as I didn't want to pry against anything that hard. There is a elbow that locks the box into the frame rail right there so that it can't fall otu the bottom with the bolts removed. You have to slide the box back towards the wheel and then it can come down. Good luck.... it wasn't fun getting mine out.

You don't need to remove your headlight, or for that matter jack up your car....With my stock 14's, I turned the wheel all the way to the right and pulled out the inner fender liner, then got the four bolts out and just kinda pulled gently till it slid out.
Last edited by Canada on Mon May 15, 2006 5:43 pm, edited 1 time in total.

User avatar
kirktalife
2GN Member
Posts: 1266
Joined: Sun Sep 04, 2005 3:52 pm
Location: Ottawa, Ont

Post by kirktalife » Mon May 15, 2006 5:25 pm

haha this is gonna be good, i would just take off the top of the filter box and throw in a K@N and there ya go
Image

lolelectricbluesxt
2GN Member
Posts: 1184
Joined: Thu Feb 23, 2006 11:40 pm
Location: Irvine, CA.

Post by lolelectricbluesxt » Mon May 15, 2006 5:27 pm

EclecticBlue wrote: You don't need to remove your headlight, or for that matter jack up your car....With my stock 14's, I turned the wheel all the way to the left and pulled out the inner fender liner, then got the four bolts out and just kinda pulled gently till it slid out.
Quoted for truth, took me less then 10 minutes this way.

I think i turned mine all the way to the right though, the front of the tire was facing inward.
Image

User avatar
Canada
Junior Admin
Posts: 4816
Joined: Tue Jun 28, 2005 4:05 pm
Location: Island Grove, Ontario, Canada

Post by Canada » Mon May 15, 2006 5:43 pm

Thats what I said jackass



;)

lolelectricbluesxt
2GN Member
Posts: 1184
Joined: Thu Feb 23, 2006 11:40 pm
Location: Irvine, CA.

Post by lolelectricbluesxt » Mon May 15, 2006 5:48 pm

Last edited by EclecticBlue on Mon May 15, 2006 2:43 pm; edited 1 time in total
lawl! Ok! :D
Image

boostinss
2GN Member
Posts: 1296
Joined: Sun Apr 02, 2006 10:17 pm
Location: Waukesha, Wisconsin

Post by boostinss » Mon May 15, 2006 5:55 pm

goddamn i tried to do that but i couldnt peal back the liner inside the wheel well.. i prolly could get at it then.. The res is connected to the other part of the airbox that goes inside the wheel well correct?
Image
2.8 - Meth - ZZP Header/DP - gmpp Caback - Injen CAI - 2 step colder plugs - 60# injecotrs - Z speed Tuned

cgneon
2GN Member
Posts: 1734
Joined: Tue May 03, 2005 11:10 pm
Location: JUPITER, FL

Post by cgneon » Mon May 15, 2006 6:21 pm

05neonsxt wrote:yeah i saw a tube that runs from the airfilter box into the fender wall ...im guessign thats where it is at.

btw i just took a ride around the block w/ out the airbox lid and damn does it sound nice with that low grumble...cant wait to see how it sounds when i get that res out.
its gonna sound the same.. since now your pullin the air from the top open, instead of the fender. if your gonna ride like that, dont worry bout the resonator. now its just sittin there doin nothin...

although i wouldnt recommend it since you'll eat through filters really quick.
Image
Official "I'm Going to Drive My Neon till it Dies" Club #000082

User avatar
grambo
Former Moderator
Posts: 3650
Joined: Wed Aug 10, 2005 9:17 pm
Location: Tracy, NOR-CAL

Post by grambo » Mon May 15, 2006 6:22 pm

Try removing the screws.......it helps. I took mine out, at work, in the parking garage, with it on the ground.
01' Neon ACR - SOLD - Its Alive!Thx Sean!
06' Subaru WRX STI - OTS Stage II
07 - Dodge Charger SRT-8 Super Bee #0267
01' Dodge Ram 5.7 - The Mall Crawler

User avatar
03sxt
Former Jr. Admin
Posts: 11389
Joined: Wed May 11, 2005 10:53 am
Location: Conneaut, Ohio
Contact:

Post by 03sxt » Mon May 15, 2006 6:27 pm

EclecticBlue wrote:You don't need to remove your headlight, or for that matter jack up your car....With my stock 14's, I turned the wheel all the way to the right and pulled out the inner fender liner, then got the four bolts out and just kinda pulled gently till it slid out.
:withstupid:

All I did was get in the car, turn the wheels all the way to the right, remove all the screws in the fender wheel well liner and pull back on it... There's a big ugly hollow box with like two or three bolts holding it on... That's the resonator. Just spend $35 on eBay and get a CAI and you'll have that nice whistle along with the grumble. :thumbup:

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Mon May 15, 2006 6:45 pm

taking the res out is cake, listen to these guys about turnin the wheel and poppin the fender screw thingies out and bend the lining back to access the res. you can also take the wheel OFF for much easier access, but it takes time to jack and shit. I had the airbob/res out and my CAI in (including jacking the car and removing the wheel) in about 1.5 hours, working at a slow pace.

aqaurius makes a good point, but the lid protects the filter so keep it on. go ahead and remove the res tho, its safe.
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


lilolneon
2GN Member
Posts: 2827
Joined: Wed Oct 26, 2005 6:38 am
Location: Ellijay, GA

Post by lilolneon » Mon May 15, 2006 7:03 pm

other option is to drop a cherry bomb into it... BAM! no more resonator box :lol:


(I was kidding plz dont try that!)
Image
2003 Atlantic Blue SE (R.I.P. 03-06)
2003 Black SXT (R.I.P. 06-14)
2007 Silver Civic LX Coupe

ACHEAPSHOT
2GN Member
Posts: 292
Joined: Wed Jan 12, 2005 12:37 pm
Location: Norwalk, CT

Post by ACHEAPSHOT » Mon May 15, 2006 7:21 pm

Unbolt your exhaust at the manifold, and remove it completely. That oughtta make it damn loud! :lol: :lol:
Official "I'm Going to Drive My Neon till it Dies" Club #89

TNK
2GN Veteran
Posts: 17343
Joined: Fri Jun 11, 2004 12:41 pm
Location: The Evergreen State

Post by TNK » Mon May 15, 2006 7:22 pm

please do drop a cherry bomb in, and take vids, it will be hilarious!
Image

Modify Your Car - Modify Your Body - Modify Your Life
TheRandom1 wrote:My true opinion here is that the only time rubber should be stretched is when it's going over a penis.

Post Reply

Return to “General 2nd Gen Discussion”